Search found 417 matches
- Thu Nov 09, 2023 6:10 pm
- Forum: DIYers
- Topic: Best (and not too expensive) center mounted sensors?
- Replies: 9
- Views: 6226
Re: Best (and not too expensive) center mounted sensors?
I didn't see the UFO cross bar install as DIY. There was no drilling or cutting involved for the snare. I just removed the opposing lugs and attached the crossbar using the lug bolts - adjusted the crossbar to center the piezo - tightened everything and then used a metal yardstick across the top of ...
- Thu Nov 09, 2023 5:44 pm
- Forum: DIYers
- Topic: DIY: 3+ Cone Builds!!!
- Replies: 52
- Views: 55507
Re: DIY: 3+ Cone Builds!!!
Hi Wayne, Although my UFO cross bar plus side mounted piezo is working well enough I do occasionally hot spot and I have to favor one side of the snare for rim clicks. I know a shop that could cut the 1/4 board. I think they could also modify your cad file to 8 lugs. I would be very appreciative if ...
- Thu Nov 09, 2023 5:31 pm
- Forum: DIYers
- Topic: Help with hi-hat closure
- Replies: 99
- Views: 74401
Re: Help with hi-hat closure
This thread is helpful - my travel was 3.3 centimeters. I adjusted it to 2.5 - it plays better
- Tue Oct 31, 2023 9:10 pm
- Forum: DIYers
- Topic: DIY: 3+ Cone Builds!!!
- Replies: 52
- Views: 55507
Re: DIY: 3+ Cone Builds!!!
Hi Wayne, The looks pretty straight forward to fabricate. I have a few questions if you don't mind: 1. How thick is the plate you mounted the piezo's on? 2. It looks you're using three of the home depot brackets to mount the plate to the shell. Are you re-using the lug screws to mount the brackets? ...
- Fri Oct 27, 2023 2:09 am
- Forum: eDRUMin
- Topic: Any interest in a touchscreen control for eDRUMin?
- Replies: 16
- Views: 19192
Re: Any interest in a touchscreen control for eDRUMin?
Having the eDRUMin control screen always available (I usually have Superior Drummer full screen) and controlled by a more precise control is an attractive idea.
- Sat Sep 16, 2023 11:25 pm
- Forum: DIYers
- Topic: some help needed on first attempt to connect
- Replies: 20
- Views: 12024
Re: some help needed on first attempt to connect
Sounds like you're out of the woods and well on your way to a well playing edrum setup. My 5 piece Ludwig Accent Combo with UFO cross bar triggers and 3 Yamaha PCY-155 for ride and crashes (PCY-135 for hi-hats mounted on a Ludwig hi-hat stand with a DIY Hall effect sensor mounted in a little project...
- Sat Sep 16, 2023 8:03 pm
- Forum: DIYers
- Topic: some help needed on first attempt to connect
- Replies: 20
- Views: 12024
Re: some help needed on first attempt to connect
There isn't a written in stone note assignment standard for edrum hardware and software. Even Superior Drummer note assignments vary depending on the kit designers. I think the goal should be to simplify as best you can but anticipate that you will need to tweak different kits. This makes sense beca...
- Thu Aug 24, 2023 7:12 pm
- Forum: DIYers
- Topic: Center mounted vs 3 cone Snare?
- Replies: 12
- Views: 9304
Re: Center mounted vs 3 cone Snare?
Hi Rob,
Do I have it right from reading your previous post that the eDRUMin can do positional sensing for the center and off-center with 3 cone sensor setups but not the edge hits?
Thanks,
Doug
Do I have it right from reading your previous post that the eDRUMin can do positional sensing for the center and off-center with 3 cone sensor setups but not the edge hits?
Thanks,
Doug
- Fri Aug 11, 2023 11:11 pm
- Forum: eDRUMin
- Topic: Where's Rob?
- Replies: 11
- Views: 1862
Re: Where's Rob?
ED8 should be available mid September. I'm using my prototype as my main eDRUMin with an ED10 in the host port. I'm pretty happy with the ED8. The size and feature set strike a good balance. Looking forward to checking out the ED8 and hope you can enjoy some quiet time. Everyone, stop fiddling arou...
- Fri Jun 16, 2023 8:24 pm
- Forum: eDRUMin
- Topic: Planning a new eDRUMin family member
- Replies: 22
- Views: 6270
Re: Planning a new eDRUMin family member
Hi Rob, I always read Digital Drummer when it arrives. I've noticed several new snares that feature multiple sensors such as three in the center and more at the edges. I think the purpose is to even out the response and improve positional sensing. I'm curious if you've looked into accommodating such...